Category: Concrete Restoration

Form Flo P-38 – Turbo Spec Sheet.docx

FormFlo P-38 – Turbo is a 1-component, polymer-modified, high-flow, concrete mix with high-early strength and extended working time. P-38 – Turbo is mixed with water and applied from 1″ to 24″ thick. Product includes 3/8″ aggregate, polymer, shrinkage-compensation, corrosion protection, flow agents and other modifiers. Designed for general purpose and high-performance concrete repair and restoration applications.

 

For Best Results
Apply to a clean, dry, sound concrete substrate with ambient and substrate temperature above 40° F. Substrate is to be saturated surface dry (SSD), if applicable, but otherwise hold no standing water prior to application. Do not re-temper already mixed material. Do not expose to rain or flowing water during application. Material should be 70 degrees + 5 degrees prior to mixing. After application, check moisture content (mat test) prior to applying any waterproof topping.

 

Surface Preparation
Surface preparation is critical to achieve long lasting results. Existing concrete substrate shall be clean, sound, and free of oil, grease, laitance, curing compounds, or any other foreign matter. Remove any remaining foreign substances and unsound concrete using mechanical methods, such as sandblasting or shotblasting. Saw cut patches at least 1″ deep and provide a square shoulder. Undercut any exposed rebar 1″ to provide adequate space for material to encapsulate the reinforcement and remove any rust present on reinforcement. Apply JE Tomes B-1 Rebar Coating to exposed reinforcement. When applicable, prior to applying FormFlo P-38 – Turbo, concrete substrates should be saturated with clean water. Just before applying product, remove any standing water and allow surface to dry. This will leave the substrate saturated surface dry (SSD). A dry substrate may pull moisture from the mixed product during placement and cause cracking or poor bond.

 

Mixing Guidelines
Force mixing is recommended with a slow speed drill with a paddle mixer or appropriately sized mortar mixer. Barrel mixers are not recommended. Approximately 3 quarts of water is required to mix 60 lbs. of product. When using a hand drill, add dry product slowly into water while mixing or introduce product in increments and mix in between to reduce lumping and ensure consistency. Mix for 1-minute, varying depth of paddle in mixing container. Allow to sit 30 seconds, thus allowing additives to take effect. Continue mixing for an additional 1 minute until homogeneous, adding water as needed to reach desired consistency. Do not exceed 3.25 quarts of water. Consistency should be very flowable to fluid without signs of aggregate segregation.

Form Flo P-38 is a 1 component, polymer modified, high-performance concrete mix. Form Flo P-38 is mixed with water and applied from 3/4″ thick to 24″. Product includes 3/8″ aggregate, corrosion inhibitor, air entrainment, and flow agents.

Form Flo P-51 is a 1 component, high flow concrete mix. Form Flo P-51 is mixed with water and applied from 1″ thick to 24″. Product includes 3/8″ aggregate, flow agents, air entrainment, and corrosion inhibitor.

TintCrete™ Colored Concrete Mix is a 1 component, polymer modified, high performance concrete mix. TintCrete™ Colored Concrete is mixed with water and applied from 3/4″ thick to 24″. Product includes 3/8″ aggregate, corrosion inhibitor, air entrainment, and flow agents. Available in 14 standard colors.

CT-40 Do All Mortar is a 1 component, polymer modified, high performance concrete repair mortar with integral corrosion inhibitor. CT-40 Do All Mortar is simply mixed with water and applied from featheredge to 1 1/2″ thick in one application. Apply horizontal, vertical or overhead. Product sets in approximately 20 minutes and is ready for light traffic in 3 to 4 hours at 70 degrees Fahrenheit.

Quick Set Latex Concrete Repair Patch is a one component, polymer modified, high performance repair mortar. Quick Set Latex Concrete Repair Patch is simply mixed with water and applied to concrete from featheredge to 1 1/2″ thick in one application. Apply horizontal, vertical or overhead. Apply with trowel, brush or broom. Product sets in 20 to 45 minutes and is ready for light traffic in 3 to 4 hours at 70 degrees Fahrenheit.

       

TintCrete™ Colored Concrete Patch is a 1 component, polymer modified, high performance decorative color concrete repair and resurfacing mortar that is available in 14 standard colors to reduce the appearance of repairs. TintCrete™ Tinted Cement Patch is simply mixed with water and applied from featheredge to 1 1/2″ thick in one application. Apply horizontal, vertical or overhead. Product sets in 20 to 45 minutes and ready for light traffic in 3 to 4 hours at 70 degrees Fahrenheit.

Dry Latex Concrete is a 1 component, polymer modified, high performance concrete repair and resurfacing mortar. Dry Latex Concrete cures to a light gray color to imitate freshly poured concrete. It is simply mixed with water and applied from featheredge to 1/4″ thick in one application. Apply horizontal, vertical or overhead. Product sets in approximately 1 hour and is ready for light traffic in 6 to 8 hours at 70 degrees Fahrenheit when broomed or brushed.

TintCrete™ Concrete Colored Resurfacer is a 1 component, polymer modified, high performance concrete repair and resurfacing mortar. TintCrete™ Color Resurfacer is available in 2 standard colors. It is simply mixed with water and applied from featheredge to 1/4″ thick in one application. Apply horizontal, vertical or overhead. Product sets in approximately 1 hour and is ready for light traffic in 6 to 8 hours at 70 degrees Fahrenheit when broomed or brushed.

JOIN OUR NEWSLETTER